Medion MD 9901 Especificações

CHAPTER 1 INTRODUCTION1-1The MICRO ATX ZX mainboard is a high-performance personal computermainboard based on the Intel® Pentium® II/Pentium® III/Cel

CHAPTER 2 HARDWARE INSTALLATION2-5SENSOR+12VGNDCPUFAN2.1-4 Fan Power Connectors: CPUFAN/PSFAN/SYSFANThese connectors support system cooling fan with

CHAPTER 2 HARDWARE INSTALLATION2-62.2 Clear CMOS Jumper: JBAT1A battery must be used to retain the mainboard configuration in CMOSRAM. Short 1-2 p

CHAPTER 2 HARDWARE INSTALLATION2-72.3 Memory Installation2.3-1 Memory Bank ConfigurationThe mainboard supports a maximum memory size of 256MB (8M x 8

CHAPTER 2 HARDWARE INSTALLATION2-8A. How to install a DIMM Module1. The DIMM slot has a two Notch Key “VOLT and DRAM”, so theDIMM memory module can

CHAPTER 2 HARDWARE INSTALLATION2-91. Supports only SDRAM DIMM.2. To operate properly, at least one 168-pin DIMM module must be installed.3. This

CHAPTER 2 HARDWARE INSTALLATION2-102.4 Case Connector: JFPThe Power Switch, Reset Switch, Power LED, Speaker, Keylock and HDDLED are all connected

CHAPTER 2 HARDWARE INSTALLATION2-112.4-1 Power SwitchConnect to a 2-pin push button switch. This switch has the same featurewith JRMS1.2.4-2 Reset Sw

CHAPTER 2 HARDWARE INSTALLATION2-122.5 Floppy Disk Connector: FDDThe mainboard also provides a standard floppy disk connector that sup-ports 360K, 7

CHAPTER 2 HARDWARE INSTALLATION2-132.6 Hard Disk Connectors: IDE1 & IDE2The mainboard has a 32-bit Enhanced PCI IDE Controller that provides PIOm

CHAPTER 2 HARDWARE INSTALLATION2-142.7 Power Supply2.7-1 ATX 20-pin Power Connector: JWR1This connector supports the power button on-board. Using t

CHAPTER 1 INTRODUCTION1-21.1 Mainboard FeaturesCPUl Slot 1 for Intel® Pentium® II/Pentium® III/CeleronTM processor.l Supports 233MHz, 266MHz, 300MHz

CHAPTER 2 HARDWARE INSTALLATION2-152.7-2 Remote Power On/Off Switch: JRMS1Connect to a 2-pin push button switch. During OFF state, press once andth

CHAPTER 2 HARDWARE INSTALLATION2-162.8 IrDA Infrared Module Connector: IRThe mainboard provides one 5-pin infrared (IR) connector for IR modules.Thi

CHAPTER 2 HARDWARE INSTALLATION2-172.9 Serial Port Connectors: COM 1 and COM 2The mainboard has a 9-pin male DIN connector for serial port COM 1. T

CHAPTER 2 HARDWARE INSTALLATION2-182.10 Parallel Port Connector: LPTThe mainboard provides a 25 pin female centronic connector for LPT. Aparallel po

CHAPTER 2 HARDWARE INSTALLATION2-192.11 Mouse Connector: JKBMS1The mainboard provides a standard PS/2® mouse mini DIN connector forattaching a PS/2®

CHAPTER 2 HARDWARE INSTALLATION2-202.14 Audio Port ConnectorsLine Out is a connector for Speakers or Headphones. Line In is used forexternal CD playe

CHAPTER 2 HARDWARE INSTALLATION2-212.15 USB ConnectorsThe mainboard provides a UHCI(Universal Host Controller Interface)Universal Serial Bus root for

CHAPTER 2 HARDWARE INSTALLATION2-225 1VGA2.16 VGA DB 15 Pin ConnectorThe mainboard provides a DB 15-pin connector to connect to a V

CHAPTER 2 HARDWARE INSTALLATION2-232.17 Power Saving Switch Connector: JGS1Attach a power saving switch to JGS1. When the switch is pressed, thesys

CHAPTER 2 HARDWARE INSTALLATION2-242.18 Power Saving LED Connector: JGL1 JGL1 can be connected with two-color LED. There are two types of LEDthat yo

CHAPTER 1 INTRODUCTION1-3On-Board Peripheralsl On-Board Peripherals include:- 1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbyt

CHAPTER 2 HARDWARE INSTALLATION2-252.19 Wake-Up on LAN Connector: JWOLThe JWOL connector is for use with LAN add-on cards that supports WakeUp on LAN

CHAPTER 2 HARDWARE INSTALLATION2-262.20 Modem Wake Up Connector: JMDM1The JMDM1 connector is for used with Modem add-on card that supportsthe Modem W

CHAPTER 2 HARDWARE INSTALLATION2-272.21 Modem-In: J5The connector is for Modem with internal voice connector.J5SPK_IN is connected to the Modem Spea

CHAPTER 2 HARDWARE INSTALLATION2-282.22 AUX Line In Connector: J7This connector is used for DVD Add on Card with Line In connector.J7GNDLR

CHAPTER 2 HARDWARE INSTALLATION2-292.23 CD-In Modem Connector: J8This connector is for Modem with internal voice connector.J8L GND R

CHAPTER 2 HARDWARE INSTALLATION2-302.24 Keyboard Power: JVSB1The JVSB1 jumper is for setting keyboard power. This function is providedby keyboard and

CHAPTER 3 AWARD® BIOS SETUP3-1Chapter 3AWARD® BIOS SETUPAward® BIOS ROM has a built-in Setup program that allows users to modifythe basic system confi

CHAPTER 3 AWARD® BIOS SETUP3-23.1 Entering SetupPower on the computer and press <Del> immediately to allow youto enter Setup. The other way to

CHAPTER 3 AWARD® BIOS SETUP3-33.3 The Main MenuOnce you enter Award® BIOS CMOS Setup Utility, the Main Menu (Figure 1)will appear on the screen. The

CHAPTER 3 AWARD® BIOS SETUP3-4Chipset Features SetupThis setup page includes all the items of chipset special features.Power Management SetupThis cate

CHAPTER 1 INTRODUCTION1-4Mountingl 6 mounting holes.System Hardware Monitor (optional)l CPU/Power Supply/Chassis Fan Revolution Detectl CPU Fan

CHAPTER 3 AWARD® BIOS SETUP3-53.4 Standard CMOS SetupThe items in Standard CMOS Setup Menu are divided into 10 catego-ries. Each category includes no

CHAPTER 3 AWARD® BIOS SETUP3-6DateThe date format is <day><month> <date> <year>.Day Day of the week, from Sun to Sat, determin

CHAPTER 3 AWARD® BIOS SETUP3-7If the controller of HDD interface is ESDI, the selection shall be“Type 1”.If the controller of HDD interface is SCSI, t

CHAPTER 3 AWARD® BIOS SETUP3-83.5 BIOS Features SetupROM PCI/ISA BIOS (2A69KM4J)BIOS FEATURES SETUPAWARD SOFTWARE, INC.Esc : Quit ↑ ↓ → ← : Select i

CHAPTER 3 AWARD® BIOS SETUP3-9CPU Internal CacheThe default value is Enabled.Enabled (default) Enable cacheDisabled Disable cacheNote: The internal ca

CHAPTER 3 AWARD® BIOS SETUP3-10Boot From LAN FirstDuring Enabled, if there’s a LAN card onboard, the priority bootingwill be from the LAN.Boot Sequenc

CHAPTER 3 AWARD® BIOS SETUP3-11Security OptionThis category allows you to limit access to the system and Setup,or just to Setup.System The system will

CHAPTER 3 AWARD® BIOS SETUP3-12Video BIOS ShadowDetermines whether video BIOS will be copied to RAM for fasterexecution. Video shadow will increase t

CHAPTER 3 AWARD® BIOS SETUP3-13SDRAM Configuration by :SPDSDRAM RAS to CAS Delay :3SDRAM RAS Precharge Time :3SDRAM CAS Latency Time :3DRAM Data Integ

CHAPTER 3 AWARD® BIOS SETUP3-14SDRAM Configuration byChoose SPD, the SDRAM time will load from the DIMM EEPROMvalue. Choose manual, the value will be

CHAPTER 1 INTRODUCTION1-5PCI SLOT 3PCI SLOT 2PCI SLOT 1ATXPower SupplyFW82443ZXSLOT 1DIMM 2Top: MouseTop: Port 1USBDIMM 1IDE2Bottom:Port 2IDE1FDDFW82

CHAPTER 3 AWARD® BIOS SETUP3-15Video BIOS CacheableSelect Enabled allows caching of the system BIOS ROM at C0000h-F7FFFh, resulting in better video pe

CHAPTER 3 AWARD® BIOS SETUP3-16Passive ReleaseWhen Enabled, CPU to PCI bus accesses are allowed duringpassive release. Otherwise, the arbiter only ac

CHAPTER 3 AWARD® BIOS SETUP3-173.7 Power Management SetupThe Power Management Setup will appear on your screen like this:ROM PCI/ISA BIOS (2A69KM4J)PO

CHAPTER 3 AWARD® BIOS SETUP3-18Power ManagementUser Define Users can configure their own powermanagement.Min Saving Pre-defined timer values are used

CHAPTER 3 AWARD® BIOS SETUP3-19Video Off AfterThe settings are N/A, Standby, Doze, or Suspend. This option is forchoosing the setting in which the mon

CHAPTER 3 AWARD® BIOS SETUP3-20HDD Power DownDisable HDD’s motor will not shut off.1 Min/2 Min/3 Min/4 Min/5 Min/6 Min/7 Min/8 Min/ 9 Min/10

CHAPTER 3 AWARD® BIOS SETUP3-21Throttle Duty CycleThis option will determine how much power will be used by theCPU , if the system goes into suspend m

CHAPTER 3 AWARD® BIOS SETUP3-22Power on by AlarmThis function is for setting date and time for your computer to bootup. During Disabled, you cannot u

CHAPTER 3 AWARD® BIOS SETUP3-23Reload Global Timer EventsIRQ[3-7,9-15], NMI : EnabledPrimary IDE 0 : EnabledPrimary IDE 1 : DisabledSecondary IDE 0 :

CHAPTER 3 AWARD® BIOS SETUP3-243.8 PNP/PCI Configuration SetupYou can manually configure the PCI Device’s IRQ. The followingpages tell you the options

CHAPTER 2 HARDWARE INSTALLATION2-1Chapter 2HARDWARE INSTALLATION2.1 Central Processing Unit: CPUStep 1: Install the Retention Mechanism.Attach the R

CHAPTER 3 AWARD® BIOS SETUP3-25Resources Controlled ByBy Choosing “Auto”, the system BIOS will detect the systemresource and automatically assign the

CHAPTER 3 AWARD® BIOS SETUP3-26IRQ-15 assigned to : PCI/ISA PnPDMA-0 assigned to : PCI/ISA PnPDMA-1 assigned to : PCI/ISA PnPDMA-3 assign

CHAPTER 3 AWARD® BIOS SETUP3-273.9 Load BIOS/Setup DefaultsThis Main Menu item loads the default system values. If the CMOSis corrupted, the defaults

CHAPTER 3 AWARD® BIOS SETUP3-283.10 Integrated PeripheralsROM PCI/ISA BIOS (2A69KM4J)INTEGRATED PERIPHERALSAWARD SOFTWARE, INC.IDE HDD Block ModeEnab

CHAPTER 3 AWARD® BIOS SETUP3-29IDE Secondary Slave PIOAuto/Mode0/Mode1-4For these 4 IDE options, choose “Auto” to have the system BIOSauto detect the

CHAPTER 3 AWARD® BIOS SETUP3-30USB Keyboard SupportEnabled/Disabled Choosing Enabled will allow the systemto use USB keyboard without a devicedriver.I

CHAPTER 3 AWARD® BIOS SETUP3-31Onboard FDC ControllerEnabled/Disabled The system has an on-board Super I/Ochip with a FDD controller that supports2 FD

CHAPTER 3 AWARD® BIOS SETUP3-32UART Mode SelectThis item allows you to determine which Infra Red (IR) function ofonboard I/O chip.Onboard Parallel Por

CHAPTER 3 AWARD® BIOS SETUP3-33channels 3 or 1. The onboard parallelport is EPP Spec. compliant, so after theuser chooses the onboard parallel portwi

CHAPTER 3 AWARD® BIOS SETUP3-343.11 Supervisor/User Password SettingThis Main Menu item lets you configure the system so that a pass-word is required

CHAPTER 2 HARDWARE INSTALLATION2-22.1-2 CPU Core Speed Derivation Procedure1 2 3 4 Core/Bus RatioON OFF ON ON 2.5ON ON OFF ON 3ON OFF OFF ON 3.5ON ON

CHAPTER 3 AWARD® BIOS SETUP3-35 HARD DISKS TYPE SIZE CYLS HEADS PRECOMP LANDZONE SECTOR MODEPrimary Master: Auto 0 0 0 0 0 0 AUTOPrimary Slave : Aut

CHAPTER 4VGA DRIVER4-1Chapter 4nVIDIA TNT2 M64 VGA DRIVER1. OverviewThe nVIDIA TNT2 M64 is a highly integrated graphics controller. Incorpo-rated w

CHAPTER 4VGA DRIVER4-21.2 System RequirementsThis section describes system requirements for the VGA Driver installa-tion and Usage.Computer Intel® Pe

CHAPTER 4VGA DRIVER4-32. nVIDIA TNT2 M64 Driver Setup & UsageProceduresInsert the CD-title into your CD-ROM drive. This CD will auto-run.This w

CHAPTER 4VGA DRIVER4-42.1-2 Changing resolution, color depth, and refresh rate:Step 1: Click Start menu and select Control Panel from Settingsgroup.

CHAPTER 4VGA DRIVER4-52.2 Windows® NT 4.0You need to install Windows® NT “Service Pack”, before you installWindows® NT driver.2.2-1 Display Driver In

CHAPTER 4VGA DRIVER4-62.2-2 Changing resolution, color depth, and refresh rate:Step 1: Click Start menu and select Control Panel from Settingsgroup.

CHAPTER 5AUDIO DRIVER5-1Chapter 5CREATIVE® AUDIO DRIVER1. OverviewThe Creative® ES1373 digital controller provides the next generation of audioperfo

CHAPTER 5AUDIO DRIVER5-22. Audio Driver Setup & Usage ProceduresInsert the CD-title into your CD-ROM drive. This CD will auto-run.This will disp

CHAPTER 5AUDIO DRIVER5-32.2 Windows® NT 4.02.2-1 Audio Driver Installation Procedure:Step 1: Click Start menu and select Control Panel from Settingsg

CHAPTER 2 HARDWARE INSTALLATION2-32.1-3 CPU Speed Setting: SW1To adjust the speed of the CPU, you must know the specification of yourCPU (always ask

CHAPTER 2 HARDWARE INSTALLATION2-4400MHz450MHz350MHzCPUTypeSW1b. 100MHz CPU Bus FrequencyTable 2.1 233 ~ 333MHz Intel® Pentium® II/III/CeleronTMproc